[TGrid] Meshing Linear Cascade in TGrid

bobus.aurelius · February 2, 2011, 11:18

Hi,

I'm new to turbomachinery. I was wondering if it is possible to mesh a linear cascade in TurboGrid. If so, then how?

Thanks and regards

bobus.aurelius · February 3, 2011, 08:32

Would really appreciate some help guys

BrolY · February 3, 2011, 09:22

You should start with the tutorials.
Then try to mesh by yourself.
And then, come back here with your questions/issues by showing us pictures.

Good luck !

bobus.aurelius · February 3, 2011, 10:31

Thanks a lot! I have gone through the tutorials and am able to mesh with Turbogrid but I wasn't able to find a way to solve my problem.

I will try to make my question a little more specific. I am trying to simulate the flow through a HP NGV linear cascade. The geometry and experimental results that I'll use for validation are from the VKI LS-89 test case.

In this case, my hub and shroud geometries are basically flat plates and the instances of the blade need to be repeated linearly and not in an annular fashion. The picture below shows the kind of thing I'm going for (although the final topology maybe different).

Turbogrid doesn't let me load the blade geometry without the hub and shroud. And as soon as I load points that would make up the corners of the flat plates for the hub and shroud, TurboGrid rotates them into a disk.

My primary question is can TurboGrid mesh linear cascades? If it can then I am prepared to spend time on finding the solution (although a few pointers would be well appreciated).

I don't know if my question is clear or even worthy of a response even now.

Thanks again though.

Jack001 · August 23, 2016, 14:14

Did you find a solution to this? It indeed would be nice if TG could produce simple cascades

February 2, 2011, 11:18	Meshing Linear Cascade in TGrid	#1
bobus.aurelius New Member Join Date: Feb 2011 Posts: 3 Rep Power: 15	Hi, I'm new to turbomachinery. I was wondering if it is possible to mesh a linear cascade in TurboGrid. If so, then how? Thanks and regards

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
solution diverges when linear upwind interpolation scheme is used	subash	OpenFOAM	0	May 29, 2010 02:23
IdeasUnvToFoam Bug amp Fix	benru	OpenFOAM Bugs	42	November 13, 2009 08:59
finding flow angle in linear cascade analysis	kiran	CFX	3	April 17, 2008 23:43
meshing a wing with tgrid	sandeep varma	FLUENT	2	April 16, 2007 04:38
TGRID & Meshing	Eric	FLUENT	3	February 13, 2002 11:52

February 3, 2011, 08:32		#2
bobus.aurelius New Member Join Date: Feb 2011 Posts: 3 Rep Power: 15	Would really appreciate some help guys

February 3, 2011, 09:22		#3
BrolY Senior Member AB Join Date: Sep 2009 Location: France Posts: 323 Rep Power: 22	You should start with the tutorials. Then try to mesh by yourself. And then, come back here with your questions/issues by showing us pictures. Good luck !

February 3, 2011, 10:31		#4
bobus.aurelius New Member Join Date: Feb 2011 Posts: 3 Rep Power: 15	Thanks a lot! I have gone through the tutorials and am able to mesh with Turbogrid but I wasn't able to find a way to solve my problem. I will try to make my question a little more specific. I am trying to simulate the flow through a HP NGV linear cascade. The geometry and experimental results that I'll use for validation are from the VKI LS-89 test case. In this case, my hub and shroud geometries are basically flat plates and the instances of the blade need to be repeated linearly and not in an annular fashion. The picture below shows the kind of thing I'm going for (although the final topology maybe different). Turbogrid doesn't let me load the blade geometry without the hub and shroud. And as soon as I load points that would make up the corners of the flat plates for the hub and shroud, TurboGrid rotates them into a disk. My primary question is can TurboGrid mesh linear cascades? If it can then I am prepared to spend time on finding the solution (although a few pointers would be well appreciated). I don't know if my question is clear or even worthy of a response even now. Thanks again though.

August 23, 2016, 14:14		#5
Jack001 Member Jack Join Date: May 2015 Posts: 98 Rep Power: 11	Did you find a solution to this? It indeed would be nice if TG could produce simple cascades