[ICEM] Blade passage block mesh in ICEM

Attesz · February 9, 2010, 07:48

Hi all,

I'm doing a cf.compressor simulation. To get the best results, i want to generate a structured, blocked hexa mesh in ICEM, only for a blade passage. Previously I made tetra mesh for this, but I'm beginner in blocking. I'm doing now the tutorials, but I think, the blocking of the blade passage is more complicated. Have anyone a tutorial, or just a good image about a hexa mesh in cf. compressor, cp.turbine., cf.pump or same turbomachinery, something to start with?

Thanks a lot,
Attesz

jeevankumarb · February 10, 2010, 02:31

Dear Attesz

If you can send the geometry, i will do the blocking and will create a ppt and will send you.

Thank you
jeevan

Attesz · February 10, 2010, 07:04

Dear jeevan,

thank you for your reply. I'm working on the geometry now, when I'm ready, I send it!

Thanks again,
Attesz

PSYMN · February 13, 2010, 02:10

There is also a "stator" tutorial in the basic tutorial set.

Attesz · February 13, 2010, 05:53

Thank you, I've already made it since I wrote this post.

Regards,
Attesz

February 9, 2010, 07:48	Blade passage block mesh in ICEM	#1
Attesz Senior Member Attesz Join Date: Mar 2009 Location: Munich Posts: 368 Rep Power: 17	Hi all, I'm doing a cf.compressor simulation. To get the best results, i want to generate a structured, blocked hexa mesh in ICEM, only for a blade passage. Previously I made tetra mesh for this, but I'm beginner in blocking. I'm doing now the tutorials, but I think, the blocking of the blade passage is more complicated. Have anyone a tutorial, or just a good image about a hexa mesh in cf. compressor, cp.turbine., cf.pump or same turbomachinery, something to start with? Thanks a lot, Attesz

February 10, 2010, 02:31	RE:	#2
jeevankumarb Member jeevan kumar Join Date: Mar 2009 Posts: 88 Rep Power: 17	Dear Attesz If you can send the geometry, i will do the blocking and will create a ppt and will send you. Thank you jeevan

February 13, 2010, 02:10	Stator	#4
PSYMN Senior Member Simon Pereira Join Date: Mar 2009 Location: Ann Arbor, MI Posts: 2,663 Blog Entries: 1 Rep Power: 47	There is also a "stator" tutorial in the basic tutorial set.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
problem when converting mesh (made by ICEM) using fluentMeshToFoam	Forrest_Lei	OpenFOAM	11	October 16, 2009 07:28
Hex-Tet Mesh Merge in ICEM	Tristan	CFX	1	September 26, 2008 06:40
BL from surface mesh on ICEM	Davide	CFX	0	August 14, 2008 07:45
ICEM block mesh with a ball in a cylinder tube	Li	CFX	6	August 11, 2008 06:44
ICEM clustering of mesh points and multiple edges	webhaw	CFX	4	July 25, 2007 17:29

February 10, 2010, 07:04		#3
Attesz Senior Member Attesz Join Date: Mar 2009 Location: Munich Posts: 368 Rep Power: 17	Dear jeevan, thank you for your reply. I'm working on the geometry now, when I'm ready, I send it! Thanks again, Attesz

February 13, 2010, 05:53		#5
Attesz Senior Member Attesz Join Date: Mar 2009 Location: Munich Posts: 368 Rep Power: 17	Thank you, I've already made it since I wrote this post. Regards, Attesz