[Workbench] An error with workbench

Ahmed Saeed Mansour · September 5, 2016, 12:53

Hello, I got these errors and I cannot start the license..I have uninstalled the program and reinstalled it then I got them...what is the solution?

Kapi · September 5, 2016, 20:59

license server is not pointing to right path!

Ahmed Saeed Mansour · September 6, 2016, 11:15

Now the licensing interconnect and licensing interconnect monitoring are running but some analysis systems are loaded when I start workbench like the fluid flow solvers but the steady and transient heat are not loaded so how can I set the right path?...thanks

Ahmed Saeed Mansour · September 6, 2016, 13:55

I wanna uninstall the server utility..How can I uninstall it ...I have succeeded in reaching this step..Thanks

Ahmed Saeed Mansour · September 6, 2016, 14:32

Thanks..I have followed this video and it works
https://www.youtube.com/watch?v=RCuyekSOHNA

Ahmed Saeed Mansour · September 6, 2016, 15:52

Now I uninstalled the program and the server utility, I wanna know please what is the right paths that I should install the program in?

Ahmed Saeed Mansour · September 6, 2016, 16:52

I got this message..errors are detected..what are the recommendations?

Kapi · September 6, 2016, 20:35

check the error on given path!
run the license manager and specify the license server!
you should be good to go!

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
ANSYS Workbench on "Uncertified" Linux Distros	hsr	CFX	289	April 20, 2023 10:23
FLUENT installation on UBUNTU 12.04 (LTS)	teymourj	FLUENT	2	March 1, 2017 23:24
[ANSYS Meshing] Workbench 13: Structured Hexa Meshes	rooftop	ANSYS Meshing & Geometry	19	March 31, 2016 03:33
Remeshing with INTEGRATED Workbench	bertozzi_marco	CFX	0	December 21, 2014 08:49
Question on running CFX simulations in workbench parameter set table	Anna Tian	CFX	0	September 20, 2014 02:51

September 5, 2016, 20:59		#2
Kapi Senior Member Join Date: Apr 2014 Location: Melbourne Posts: 584 Rep Power: 14	license server is not pointing to right path!

September 6, 2016, 11:15		#3
Ahmed Saeed Mansour Senior Member Have a nice time! Join Date: Feb 2016 Location: mech.eng.ahmedmansour@gmail.com Posts: 291 Rep Power: 11	Now the licensing interconnect and licensing interconnect monitoring are running but some analysis systems are loaded when I start workbench like the fluid flow solvers but the steady and transient heat are not loaded so how can I set the right path?...thanks

September 6, 2016, 14:32		#5
Ahmed Saeed Mansour Senior Member Have a nice time! Join Date: Feb 2016 Location: mech.eng.ahmedmansour@gmail.com Posts: 291 Rep Power: 11	Thanks..I have followed this video and it works https://www.youtube.com/watch?v=RCuyekSOHNA

September 6, 2016, 15:52		#6
Ahmed Saeed Mansour Senior Member Have a nice time! Join Date: Feb 2016 Location: mech.eng.ahmedmansour@gmail.com Posts: 291 Rep Power: 11	Now I uninstalled the program and the server utility, I wanna know please what is the right paths that I should install the program in?

September 6, 2016, 20:35		#8
Kapi Senior Member Join Date: Apr 2014 Location: Melbourne Posts: 584 Rep Power: 14	check the error on given path! run the license manager and specify the license server! you should be good to go!