[DesignModeler] ANSYS 14.5 DesignModeler - Unable to start...

martinko814@gmail.com · December 2, 2014, 18:27

Hello everybody,

i need urgent technical support.

Till last week i was using ansys r12.1, after instalation of ansys 14.5 it crashes after loading of geometrie. APDL is without problems, in full working. Licence is ok.
Instalation of 14.5 without : antivirus, firewall and offline.
I tried to repair it by recommendations to forums.
I used to repair, reinstal windows, installation new graphics drivers, i have all current C ++ Library.

Technical parameters PC:
AMD FX 8350, RAM 16GB
Quadro 600
windows 7 ultimate

THX FOR YOUR KNOWINGS SUPPORTS

without response it writes error:

Christian.Stemmer · December 12, 2014, 04:50

Knowledge Resources: Solutions

#2037921
Problem Description: Any Mechanical application - Mechanical, Meshing, Design-Modeler & FEModeler will not run after a Red Hat 6.x update: RHSA-2014:1436. Starting Design Modeler from WorkBench simply hangs for two to three minutes and then presents an error: "Unable to start the geometry editor." Mechanical also fails to start. Platform - Redhat6.x or derivatives

Product Family: Installation, Licensing & Systems
Product: ANSYS Mechanical
Version: 15.0
Area: Installation Process
SubArea: Other
Last Updated: Nov 14 2014

Answer:
Resolution:

The fix is a simple rename of a folder. In the path below rename the X11 folder to Old-X11

/ansys_inc/v150/commonfiles/MainWin/linx64/mw/lib-amd64-linux/

xdonu · May 13, 2015, 11:23

Thank you very much!!! This was driving me insane.

TallesC · October 21, 2015, 00:22

Hello,

I'm like the same problem, but not can not find the file path, so meeting up commonfiles. I use Windows 7 - 64 bit, Ansys version 16.1.

xdonu · October 21, 2015, 05:19

That path corresponds to a Linux installation not Windows. So I don't think you'll find it. Your issue is probably related to something different.

December 2, 2014, 18:27	ANSYS 14.5 DesignModeler - Unable to start...	#1
martinko814@gmail.com New Member Renegade Join Date: Dec 2014 Posts: 1 Rep Power: 0	Hello everybody, i need urgent technical support. Till last week i was using ansys r12.1, after instalation of ansys 14.5 it crashes after loading of geometrie. APDL is without problems, in full working. Licence is ok. Instalation of 14.5 without : antivirus, firewall and offline. I tried to repair it by recommendations to forums. I used to repair, reinstal windows, installation new graphics drivers, i have all current C ++ Library. Technical parameters PC: AMD FX 8350, RAM 16GB Quadro 600 windows 7 ultimate THX FOR YOUR KNOWINGS SUPPORTS without response it writes error:

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Ansys 14.5 Problem Import Mesh from ICEM CFD to CFX	Smiling Assassin	CFX	1	May 9, 2014 03:27
Mesh difference between 14.5 version and 15.0 version in ansys meshing	sunxihui	ANSYS Meshing & Geometry	0	May 6, 2014 05:22
ansys 14.5 comparability with OS	Raj14	CFX	2	February 6, 2013 00:56
How to generate the geometry of Hydrofoil impeller with Ansys designmodeler	commonyue	Main CFD Forum	0	December 15, 2011 09:43
How can I start the ANSYS 12 workbench in LINUX	Ardisia	ANSYS	3	September 7, 2010 01:19

December 12, 2014, 04:50	had the same problem - does this help?	#2
Christian.Stemmer New Member Christian Stemmer Join Date: Dec 2014 Posts: 3 Rep Power: 12	Knowledge Resources: Solutions #2037921 Problem Description: Any Mechanical application - Mechanical, Meshing, Design-Modeler & FEModeler will not run after a Red Hat 6.x update: RHSA-2014:1436. Starting Design Modeler from WorkBench simply hangs for two to three minutes and then presents an error: "Unable to start the geometry editor." Mechanical also fails to start. Platform - Redhat6.x or derivatives Product Family: Installation, Licensing & Systems Product: ANSYS Mechanical Version: 15.0 Area: Installation Process SubArea: Other Last Updated: Nov 14 2014 Answer: Resolution: The fix is a simple rename of a folder. In the path below rename the X11 folder to Old-X11 /ansys_inc/v150/commonfiles/MainWin/linx64/mw/lib-amd64-linux/

May 13, 2015, 11:23		#3
xdonu New Member Join Date: Apr 2012 Posts: 8 Rep Power: 14	Thank you very much!!! This was driving me insane.

October 21, 2015, 00:22		#4
TallesC Senior Member Talles Caio Join Date: Oct 2012 Location: Brazil Posts: 101 Rep Power: 14	Hello, I'm like the same problem, but not can not find the file path, so meeting up commonfiles. I use Windows 7 - 64 bit, Ansys version 16.1.

October 21, 2015, 05:19		#5
xdonu New Member Join Date: Apr 2012 Posts: 8 Rep Power: 14	That path corresponds to a Linux installation not Windows. So I don't think you'll find it. Your issue is probably related to something different.