CFD Online Logo CFD Online URL
www.cfd-online.com
[Sponsors]
Home > Wiki > Shuai-Agarwal turbulence Model

Shuai-Agarwal turbulence Model

From CFD-Wiki

Revision as of 02:58, 8 April 2021 by Lin.zhenghao (Talk | contribs)
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to: navigation, search

Introduction

One-equation k-kL turbulence model was developed from two-equation k-kL closure of Abdol-Hamid et al. [1]. Improvements to the original formulation of one-equation k-kL model (AIAA 2019-1879) were made by optimizing the model constants. The new improved model has been validated by simulating several benchmark canonical wall-bounded turbulent flows with small regions of separation from NASA TMR (https://turbmodels.larc.nasa.gov/). The model needs further investigations by the scientific community to evaluate its potential.

Shuai – Agarwal One Equation k-kL Turbulence Model

The turbulent viscosity is given by:


v_{t}=C_{\mu}^{1/4} \frac{kL}{{k}^{1/2}}

The final form of the new Shuai-Agarwal one-equation k-kL model is obtained as:


\frac{D v_{t}}{D t}=a_{1}\left(C_{\phi 1}-\frac{1}{2}\right) \frac{P}{S}+\left(\frac{1}{2} a_{1}-\frac{C_{\phi 2}}{\sqrt{a_{1}}}\right) v_{t} S+\frac{v v_{t}\left(1-6 f_{\phi}\right)}{d^{2}}+\frac{\sigma}{2 }\frac{v_{t}}{S} \frac{\partial v_{t}}{\partial x_{i}} \frac{\partial S}{\partial x_{i}}+\frac{3 \sigma}{4} \frac{\partial v_{t}}{\partial x_{i}} \frac{\partial v_{t}}{\partial x_{i}}-\frac{\sigma}{4} \frac{\partial S}{\partial x_{i}} \frac{\partial S}{\partial x_{i}} \frac{v_{t}^{2}}{S^{2}}+\frac{\partial}{\partial x_{i}}\left(\left(\sigma v_{t}+v\right) \frac{\partial v_{t}}{\partial x_{i}}\right)


Where P is the production term:


P=\frac{\tau_{ij}}{\rho} \frac{\partial u_{i}}{\partial y}



{\tau_{ij}}={\mu_{t}} \left(2S_{i j}-\frac{2}{3} \frac{\partial u_{k}}{\partial x_{k}}{\delta_{i j}}\right)-\frac{2}{3} {\rho}{\delta_{i j}}



S_{i j}=\frac{1}{2}\left(\frac{\partial u_{i}}{\partial y} + \frac{\partial u_{j}}{\partial x} \right)


The following Bradshaw relation is used to express the relationship between v_{t} and k and kL:


v_{t}|\frac{\partial u}{\partial y}|=C_{\mu}^{\frac{1}{2}}{k}

The parameter of the model are:


C_{\phi 1}=\left(\zeta_{1}-\zeta_{2}\left(\frac{\sqrt{\nu_{t}}}{L_{k} \sqrt{S}}\right)^{2}\right)

C_{\phi 2}={\zeta_{3}}

L_{v k}=\kappa\left|\frac{U^{\prime}}{U^{\prime \prime}}\right|

U^{\prime}=\sqrt{2}{S_{ij}}{S_{ij}}

U^{\prime \prime}=\sqrt{\left(\frac{\partial^{2} u}{\partial x^{2}}+\frac{\partial^{2} u}{\partial y^{2}}+\frac{\partial^{2} u}{\partial z^{2}}\right)^{2}+\left(\frac{\partial^{2} v}{\partial x^{2}}+\frac{\partial^{2} v}{\partial y^{2}}+\frac{\partial^{2} v}{\partial z^{2}}\right)^{2}+\left(\frac{\partial^{2} w}{\partial x^{2}}+\frac{\partial^{2} w}{\partial y^{2}}+\frac{\partial^{2} w}{\partial z^{2}}\right)^{2}}

L_{v k , max}=C_{1 2}{\kappa}{d}{f_{p}}

L_{v k , min}=\frac{\sqrt{v_{t}}}{{C_{11}}{\sqrt{S}}}

f_{p}={min}{[max(\frac{P}{{\rho}{v_{t}}{S^{2}}} , 0.5) {,}{1.0}]}

f_{\phi}=\frac{1+C_{d1}{\epsilon}}{1+\epsilon^{4}}

\epsilon=\frac{d \sqrt{0.3\frac{{v_{t}}{S}}{a_{1}}}}{20v}

\zeta_{2}=\zeta_{1}-\frac{\zeta_{3}}{C_{\mu}^{\frac{3}{4}}}+\frac{\kappa^{2}\sigma}{ C_{\mu}^{\frac{1}{2}}}

The model constants are:


\zeta_{1}=1.5

\zeta_{2}=0.95

\zeta_{3}=0.16

\kappa=0.41

a_{1}=\sqrt{C_{\mu}}=0.3

C_{11}=10.0

C_{12}=1.3

C_{d1}=4.7

\sigma=0.6

References

  • S. Shuai and R. K. Agarwal (2020), "A New Improved One-Equation Turbulence Model Based on k-kL Closure", AIAA Paper 2020-1075, January 2020.
  • K. S. Abdol-Hamid, J. R. Carlson, and C. L. Rumsey (2016), "Verification and Validation of the k-kL Turbulence Model in FUN3D and CFL3D Codes", AIAA 2016-3941, 2016.
My wiki