There is not enough space on the disk for simulation results

BRN · September 14, 2023, 13:48

Hello everyone have a nice day,

Ive downloaded REEF3D and started the first simulation. After a few hours I saw that I got no space in my C: directory (before simulationI got 11GB space), so I assume simulation outputs are stored in C directory. But the simulation folder is in \\wsl.localhost\Ubuntu\home\baranpolat\test1.

My question is can I change the directory C: to D: because I got a lot of space in D.

Any suggestions and helps are appreciated.

Thanks a lot,

Baran.

ThatHimalayanGuy · September 15, 2023, 09:21

I think you will have to reinstall WSL in the D drive. I faced the same problem before.
I remember there were some ideas to move the entire WSL from C to D drive. It might be worth looking into, saves you time.

valgrinda · September 15, 2023, 09:38

A pragmatic solution is to write out less data, see the P10/P20/P30 options.

BRN · September 15, 2023, 10:46

Actually, I moved the simulation folders to D. Created I file at D, such as test2 then put control.txt and ctrl.txt DiveMESH and REEF3D to this folder and navigate this folder in Ubuntu. Whit that way, I can manage to run the simulation without a problem.

September 14, 2023, 13:48	There is not enough space on the disk for simulation results	#1
BRN New Member Sarp Join Date: Dec 2021 Posts: 17 Rep Power: 5	Hello everyone have a nice day, Ive downloaded REEF3D and started the first simulation. After a few hours I saw that I got no space in my C: directory (before simulationI got 11GB space), so I assume simulation outputs are stored in C directory. But the simulation folder is in \\wsl.localhost\Ubuntu\home\baranpolat\test1. My question is can I change the directory C: to D: because I got a lot of space in D. Any suggestions and helps are appreciated. Thanks a lot, Baran.

September 15, 2023, 09:38		#3
valgrinda Super Moderator Hans Bihs Join Date: Jun 2009 Location: Trondheim, Norway Posts: 403 Rep Power: 19	A pragmatic solution is to write out less data, see the P10/P20/P30 options. __________________ Hans Bihs Team REEF3D www.reef3d.com

September 15, 2023, 10:46		#4
BRN New Member Sarp Join Date: Dec 2021 Posts: 17 Rep Power: 5	Actually, I moved the simulation folders to D. Created I file at D, such as test2 then put control.txt and ctrl.txt DiveMESH and REEF3D to this folder and navigate this folder in Ubuntu. Whit that way, I can manage to run the simulation without a problem. kamath likes this.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Validating the results of numerical modeling compared to the results of another model	ENG.AHMAD	FLUENT	0	June 22, 2020 17:49
bad heat transfer results with low y+	me45	OpenFOAM Running, Solving & CFD	0	April 29, 2020 12:56
Error Interpolating Results onto New Mesh	nammeh	CFX	1	March 26, 2019 13:08
Exporting Transient results as a function of space and time	sniak	CFX	4	December 6, 2017 06:43
Creating a tool to interpolate results	Luis Batista	OpenFOAM Running, Solving & CFD	2	April 11, 2013 09:15

September 15, 2023, 09:21		#2
ThatHimalayanGuy New Member rabs Join Date: Jun 2023 Posts: 5 Rep Power: 3	I think you will have to reinstall WSL in the D drive. I faced the same problem before. I remember there were some ideas to move the entire WSL from C to D drive. It might be worth looking into, saves you time.